BL 13.5 inch Mk I – IV gun

• Name — Ordnance BL 13.5 inch gun Mk I - IV • Origin — United Kingdom • Type — Naval gun • Is Ranged — YES • Is Artillery — YES • Is Uk — YES • Used By — United Kingdom Kingdom of Italy • Designer — Woolwich • Design Date — 1880 • Variants — Mk I, II, III, IV • Weight — 67-69 tons barrel & breech • Part Length — 405 in bore (30 calibres) • Cartridge — 1250 lb • Caliber — 13.5 in • Velocity — 2016 ft/s • Range — 12000 yd

• Illustration — Aft barbette mounting on battleship Empress of India in drydock at Chatham Dockyard in the 1890s The gun was designed to match the new large guns of the French battleships. Development and manufacture occurred far slower than intended. The first ships armed with the 13.5 in gun were four of the s: Anson, Camperdown, Howe and Rodney, which were laid down in 1882-83 and completed in 1888-89. The Howe and the Rodney were laid down to the same dimensions as the preceding Collingwood, which was designed for 12 in 45 ton guns. The increase in weight of the 13.5 in guns, their mountings and ammunition increased draught from 26 ft to 27 ft, and increased displacement by 800 LT. The Anson and Camperdown were laid down later, to greater dimensions. All four ships carried their 13.5 in guns in twin barbettes on the centreline at each end of the superstructure. The guns also equipped the subsequent laid down in 1886 and s laid down in 1889.

A single Mk III gun was mounted as a disappearing gun for coast defence at Penlee Battery, Plymouth.

• Illustration — Barbette mounting on Re Umberto Guns were also sold to Italy to arm the s, and, laid down in 1884 and finally commissioned in 1893 and 1895.

The gun was made up of the following parts: • A tube, • Breech-piece, • B hoop, • B tube, • 1- and 2-C hoops, • C tube, • 1- and 2D hoops, and • Jacket. Construction was as follows: • The breech-piece, B hoop and B tube were shrunk over the A tube, extending to the muzzle. • The 1-C hoop was shrunk over the breech-piece. The 1-C hoop and the breech-piece were connected longitudinally by a screwed steel bush at the breech end. The bush was prepared for receiving the breech screw. • The C tube and 2-C hoop were shrunk over the B hoop and B tube. • The 1-D hoop was shrunk round the 1-C hoop and part of the C tube. This was secured at the breech end by a screwed steel ring. • The 2-D hoop was shrunk over the C tube immediately in front of the 1 D hoop. • The jacket was shrunk round the 1-D hoop at the breech. • Thrust collars were formed on the outside of the 1-D hoop and were used to secure the gun to the gun-mounting (the gun did not have trunnions). The length of the bore was 405 in (30 calibres), of which the length of rifling was 333.4 in. The rifling used the increasing twist system; there were 54 grooves, with a twist of 1 in 120 at the breech-end rising to 1 in 30 at 166.7 in from the muzzle; the twist then remained a uniform 1 in 30. The chamber length was 66.5 in, and the volume of the chamber was 17,100 in3. The gun had a hydraulically-operated interrupted-screw breech-block. The breech-block was completely detached from the gun during loading (because there was no carrier). The guns were designed and manufactured by Woolwich Arsenal. There were significant delays in the manufacture of the guns in the 1880s, which inordinately delayed the completion of the first four battleships equipped with them. The cause of the delays was "the faulty principle of placing liners in the bores which cracked during proof and it took a long time to repair these and make the guns efficient."

The gun fired a 1,250 lb projectile using 630 lb brown powder (SBC) propellant. This gave the projectile a muzzle velocity of 2016 ft/s, which would penetrate 28.2 in wrought iron at 1000 yd. When smokeless propellant was introduced, the gun had a 187 lb cordite-44 charge, giving the 1,250 lb projectile a muzzle velocity of 2099 ft/s. The calibre radius head (crh) of the projectiles was nominally two. In the Admiral and Trafalgar classes the maximum elevation was 13 degrees. In the Royal Sovereign class and the Hood the maximum elevation was 13.5 degrees. At 13.5 degrees elevation, the maximum range with brown powder was 11,950 yd, whilst with cordite it was 12,620 yd. The projectiles used a copper driving band to engage the rifling. Once a gun had fired about 100-110 rounds with full (brown powder) charges, the rifling became worn near the breech, such that it was necessary to augment the width of the driving bands. Ships were therefore issued with "augmenting strips", which were long strips of copper that were hammered partially into the recessed ring around the projectile (cannelure) that held the driving band. Once guns were too worn for augmenting strips to help, the guns were sent back to the factory to be relined. Wear was lower when firing reduced charges. Under favourable circumstances, two 13.5 in guns in a mounting on the Anson could fire "in a couple of minutes or even less".

• 340mm/28 Modèle 1881 gun French equivalent