4.5×26mm MKR

• Name — 4.5mm MKR (synonyms: 4.5mm Interdynamic, 4.5mm Kjellgren) • Origin — Sweden • Type — Rifle • Service — Prototypes only. • Design Date — 1978 • Manufacturer — Interdynamics AB • Number — Prototypes only • Parent —.22 WMR • Case Type — Rimfire, tapered, shoulderless bottleneck • Bullet — 4.63 mm, 22 mm long, cold-rolled copper, boat-tail spitzer. • Neck — 5.02 mm • Shoulder — none • Base — 6.48 mm • Rim Dia — 7.44 mm • Case Length — 26.10 mm • Length — 42 mm • Primer — Rimfire • Max Pressure — 241–276 MPa • Filling — 0.51 grams tubular nitrocellulose powder or 0.57 grams spherical double-base powder • Bwunit — 4.5 mm (.177 in) • Bw1 — 1.58 g (24.4 gr) • Vel1 — 1,000 m/s (3,270 ft/s • En1 — 790 J (583 ft lbs) • Test Barrel Length — 640 mm

The 4.5mm MKR was designed in 1978 by Interdynamic AB, a Swedish company, around the time of the rise of "micro-caliber" popularity. Firearms companies everywhere were trying to achieve a type of practical, light and cheap ammunition. Micro-caliber (less than 5 mm in diameter) ammunition makers wished to achieve higher velocities, flatter trajectories, and greater penetration while keeping weight and recoil low as possible to facilitate controllable use in individual automatic weapons.

The 4.5mm MKR was essentially a.22 WMR rimfire case necked down from 5.6 mm to accept a 4.5 mm bullet, for use in the Interdynamics MKR rifle and carbine. It was supplied in single-use, 50-round polymer magazines. The cartridge featured a curved taper of its body to aid extraction and a short, shoulderless neck. Its 4.5 mm caliber boat-tail spitzer bullet was 22 mm long and made by cold rolling solid copper wire. The lightweight bullet of 1.58 g reportedly achieved a muzzle velocity of about 1,000 m/s and a muzzle energy of 790 J. This claim contrasts sharply with the comparable, more modern.17 HMR which has a muzzle energy of 340 J. Due to the combination of a thin-walled rimfire case with a high-pressure powder charge, the cartridge needed good external support so the MKR rifle was designed to use locked breech, gas-operated action with a vertically tilting bolt rather than straight blow back operation. This ensured the bolt only opened once cartridge pressure had reduced to safe levels. The rifle and carbine, which differed only in barrel length, were fired from the open bolt position to prevent cook-off ignition of the thin walled cartridges. Users could select from semi-automatic, three-round burst, or fully automatic modes. The burst and fully automatic modes had a high rate of fire of 1800 rounds per minute.

The 4.5×26 MKR was claimed to be on par with a 5.56×45mm NATO M-193 bullet at up to 300 m, while one could carry 3.5 times as many of the lighter weight cartridges. Its slender 4.5 mm projectile could penetrate a steel helmet up to 300 m, out to that range it had a similar ballistic curve to the 5.56×45 NATO with M-193 projectile. This was due to a combination of slightly higher velocity, a similar Ingalls ballistic coefficient to the M-193 bullet (0.245 vs 0.265), and the superior penetrating ability of solid cold-rolled copper bullets vs jacketed lead bullets given an equal sectional density. It was potentially lethal at up to 750 m with 80 J and its tendency to tumble on impact was twice that of the 5.56 M-193 bullet, thus ensuring more effective transfer of its diminutive energy to its target, especially as its tip tended to bend. Maximum range was 2,500 m. Due to concerns about stopping power, reliability, and the inherent problems with using rimfire ammunition, the MKR project was abandoned at the prototype stage and the 4.5mm MKR never saw service or any kind of widespread use.

The following is established of the heading itself. It is also recorded that 4.5×26mm MKR is classified as a personal defense weapon cartridge.